Contact Us

Capacity : 1250 gpm (78.8 lps)
Head : 265 ft (80.8 m)

Technical Information

The Right Choice

The 4RC and 4RCX (explosion-proof) submersible wastewater pumps are the right choice when difficult to pump fibrous or stringy solids are to be expected. The 4RC/4RCX series provides smooth, vibration-free operation when operating at heads higher than peak efficiency. The pump is for use in municipal lift stations, treatment plants and industrial waste water applications.

Myers offers a complete line of wastewater pumps, lift-out rail assemblies, controls and accessories to meet your needs.

Passes stringy trash, fibrous wastes, slurries, and other difficult to pump solids that standard enclosed or semi-open impellers cannot.

  • Recessed impeller design has completely open passage in volute.
  • Pumping action is by vortex; solids can't get caught in impeller volute.
  • Operates without vibration or cavitation over entire performance curve. Operates near shutoff without harming pump.

Durable motor will deliver many years of reliable service.

  • Recessed impeller greatly increases bearing life by reducing radial load.
  • Oil-filled motor for maximum heat dissipation and constant bearing lubrication.
  • Heat sensor thermostats imbedded in windings protect motor from overheat conditions.
  • Seal leak probes warn of moisture entry; helps prevent costly motor burnout.

Available with optional FM approval for use in Class 1, groups C and D hazardous locations (4RCX only).

Unit of Measure

Specifications

Head

 N/A 265 ft80.8 m

Solids Handling

 N/A 3 in76 mm

Liquids Handling

 N/A Effluent Fibrous Wastewater Raw Unscreened Sewage Storm Water

Intermittent Liquid Temperature

 N/A up to 140 ºFup to 60 ºC

Winding Insulation Temperature. (Class H)

 N/A 356 ºF180 ºC

Motor Electrical Data

 N/A 1150 rpm
3-15 HP, 200/230/460/575V, 3 phase, 60 Hz 1750 rpm
10-40 HP, 200/230/460/575V, 3 phase, 60 Hz 3450 rpm
20-60 HP, 230/460/575 volts, 3 phase, 60 Hz

Acceptable pH Range

 N/A 6 to 9

Specific Gravity

 N/A 0.9 to 1.1

Viscosity

 N/A 28 to 35 SSU

Horizontal Discharge Flanged Centerline

 N/A 4 in 125 lb. ANSI 101.6 mm

Speed

 N/A 1750 rpm

Power

 N/A 30 hp

Voltage

 N/A 230 V

Phase

 N/A 3

Frequency

 N/A 60 Hz

Start

 N/A 452 A180.1 kV·A

Run

 N/A 94 A33.3 kW37.4 kV·A

NEC Code Letter

 N/A G

Service Factor

 N/A 114 A41.3 kW1.2

Capacity

 N/A 1250 gpm78.8 lps

Note

 N/A Consult factory for applications outside of these recommendations.
FM, Class 1, Div. 1, Groups C & D

Construction Material

Motor Housing Material

 N/A Cast Iron, Class 30, ASTM A48

Seal Housing Material

 N/A Cast Iron, Class 30, ASTM A48

Volute Case Material

 N/A Cast Iron, Class 30, ASTM A48

Cord Cap Material

 N/A Cast Iron, Class 30, ASTM A48

Recessed Impeller Material

 N/A Ductile Iron, Class 65, ASTM A536

Power Cord Material

 N/A 35 ft. SOOW

Control Cord Material

 N/A 35 ft. SOOW

Standard Double Tandem Mechanical Seal Material

 N/A Carbon & Ceramic, Type 21

Optional Double Tandem Mechanical Seal Material

 N/A Lower Tungsten Carbide Silicon Carbide

Pump Shaft Material

 N/A 416 SST

Motor Shaft Material

 N/A 416 SST

Fasteners Material

 N/A 300 series SST

Agency Approvals

Agency Approvals

 N/A