Contact Us

Capacity : 2,320 gpm (8,800 lpm)
Head : 260 ft (79 m)

Submersible Dry Pit

Standard (8SM) and Explosion-Proof (8SMX) Construction

The Myers 8SMDP Submersible Dry Pit Non-clog Sewage Pumps are designed especially for high flow applications such as: large municipal stations, treatment plants, transfer stations and dewatering. The ability to handle solids up to 3 inches in diameter make it ideal for most high flow wastewater applications.

Advantages By Design
High efficiency hydraulic design cuts pumping costs and extends the life of the pump

  • Two-vane, rounded port impeller handles 3" solids with ease at high operating efficiencies.
  • Produces high heads and flows

Durable motor will deliver many years of reliable service

  • Class H insulation.
  • Continuous duty/VFD magnet wire.
  • Oil-filled motor for maximum heat dissipation and constant bearing lubrication.
  • Internal thermal overload protection.
  • Double tandem shaft seals prevent sewage from entering motor.
  • Internal seal leak probes warn of moisture entry.
  • Triple sealed power and control cables.
Unit of Measure

Specifications

Head

 N/A 260 ft79 m

Solids Handling

 N/A 3 in76 mm

Liquids Handling

 N/A Drain Water Effluent Raw Unscreened Sewage

Intermittent Liquid Temperature

 N/A up to 140 ºFup to 60 ºC

Winding Insulation Temperature. (Class H)

 N/A 356 ºF180 ºC

Available Motors

 N/A 1750RPM
75, 100, 125 HP
460 & 575 volt
3 phase, 60 Hz

Acceptable pH Range

 N/A 6 to 9

Specific Gravity

 N/A 0.9 to 1.1

Viscosity

 N/A 28 to 35 SSU

Horizontal Discharge

 N/A 8 in203.2 mm

Speed

 N/A 1750 rpm

Power

 N/A 100 hp

Voltage

 N/A 575 V

Phase

 N/A 3

Frequency

 N/A 60 Hz

Start

 N/A 580 A578 kV·A

Run

 N/A 103.2 A85.7 kW103.0 kV·A

NEC Code Letter

 N/A G

Service Factor

 N/A 124.0 A103.0 kW1.2

Capacity

 N/A 2,320 gpm8,800 lpm

Note

 N/A Consult factory for applications outside of those recommendations.
FM Class 1, Group C & D

Construction Material

Motor Housing Material

 N/A Cast Iron, Class 30, ASTM A48

Seal Housing Material

 N/A Cast Iron, Class 30, ASTM A48

Volute Case Material

 N/A Cast Iron, Class 30, ASTM A48

Cord Cap Material

 N/A Cast Iron, Class 30, ASTM A48

Impeller Material

 N/A Ductile Iron, Class 65 ,ASTM A536

Power Cord Material

 N/A 25 ft. SOOW

Control Cord Material

 N/A 25 ft. SOOW

Standard Double Tandem Mechanical Seal Material

 N/A Carbon & Ceramic

Optional Double Tandem Mechanical Seal Material

 N/A Lower Tungsten, Carbide

Pump Shaft Material

 N/A 416 SST

Motor Shaft Material

 N/A 416 SST

Fasteners Material

 N/A 300 series SST

Case Wear Ring Materials

 N/A Bronze

Base Elbow Material

 N/A Cast Iron, Class 30 ,ASTM A48

Agency Approvals

Agency Approvals1 N/A



  • 1 Pending