Rapid Pump & Meter Service Co., Inc. & Machinery Services Co.
Rapid Pump & Meter Service Co., Inc.
Machinery Services Co.
285 Straight Street
P.O. Box AY
Paterson, NJ, 07509 USA
Fax: 973.345.0301
Phone: 973.345.5600
Email: info@servicer.com
Website: www.rapidservice.com
Print Back
Capacity : 60 gpm (227 lpm)
Head : 124 ft (37.8 m)

1/2 and 1 HP

The Myers P Series Effluent Pumps are designed specifically for today's multi-pump pressure collection and septic tank effluent pumping (S.T.E.R) systems and high head drainage applications. The P Series effluent pumps with their high efficiency single vane, enclosed impellers provide the steep non-overloading performance curves ideal for pressure collection and S.T.E.P systems. Myers 1/2 and 1 horsepower P Series pumps deliver more capacity at higher heads than most 1,1 1/2 and 2 horsepower pumps in their class. Myers P Series pumps are constructed of only the highest quality corrosion resistant materials like cast iron, stainless steel and thermoplastics to assure that they will perform for years to come in the harsh effluent environment end drainage applications.

Advantages By Design
Optimum performance for use in multi-pump pressure collection and S.T.E.P. systems
  • High efficiency, single vane, enclosed impeller provides non-overloading performance over entire range. Outperforms most pumps in its class.
  • Impeller passes 3/4 inch spherical solids.
  • Enclosed impeller design eliminates possibility of jamming or corrosion between impeller and volute.
Durable motor will deliver many years of reliable service
  • Oil-filled motor for maximum heat dissipation and constant bearing lubrication.
  • High torque, permanent split capacitor (PSC), single phase motors. No starting switches or relays to wear out.
  • Double tandem seal option for extra motor protection, tough effluent pumping applications.
  • Optional seal leak probe warns of seal leak condition. (Dual seal motors only.) Helps prevent costly motor damage.
  • On-winding current and temperature sensitive overload to protect against costly burnout due to overload.
The P series effluent pumps are designed for years of maintenance free operation
  • Volute seal ring is replaceable. Restores pump to original performance if wear should occur.
  • Motor is held in place by four screws. Easily removed if service is ever needed.
Unit of Measure

Specifications

Head

 N/A 124 ft37.8 m

Maximum Spherical Solids

 N/A 3/4 in19 mm

Liquids Handling

 N/A Domestic Effluent & Drain Water

Intermittent Liquid Temperature

 N/A up to 140 ºFup to 60 ºC

Motor Electrical Data

 N/A 1 hp, 230 volts, 1 ph
oil-filled, permanent split capacitor type, 3450 rpm, 60 Hz 1/2 hp, 115 or 230 volts, 1 ph
oil-filled, permanent split capacitor type, 3450 rpm, 60 Hz

Motor Insulation

 N/A Class B(130°C)

Acceptable pH Range

 N/A 6 to 9

Specific Gravity

 N/A 0.9 to 1.1

Viscosity

 N/A 28 to 35 SSU

Discharge, NPT

 N/A 1 1/2 in38.1 mm

Minimum Sump Diameter (Simplex)

 N/A 24 in61 cm

Minimum Sump Diameter (Duplex)

 N/A 36 in91.4 cm

Speed

 N/A 3450 rpm

Power

 N/A 1 hp1/2 hp

Capacity

 N/A 60 gpm227 lpm

Construction Material

Motor Housing Material

 N/A Cast Iron, Class 30, ASTM A48

Volute Material

 N/A Cast Iron, Class 30, ASTM A48

Enclosed Single Vane Impeller Material

 N/A Engineered Thermoplastic

Impeller Wear Ring Material

 N/A 304 SST

Power Cord Material

 N/A 20 ft. 16/3 SJOW/SJOW-A

Volute Seal Ring Material

 N/A Buna-N

Shaft Material

 N/A 416 SST

Standard Shaft Seal Material

 N/A Single Carbon & Ceramic

Optional Lower Shaft Seal Material

 N/A Tungsten Carbide

Fasteners Material

 N/A 300 series SST

Agency Approvals

Agency Approvals

 N/A