Capacity : 7,750 gpm (29,331 lpm)
Head : 72 ft (21.9 m)

Standard (12VL) and Explosion-Proof (12VLX)

The Myers 12VL Submersible non-clog Sewage Pumps are designed especially for high flow, medium head applications such as: Large municipal lift stations, treatment plants, transfer stations and dewatering. A quick removal type rail system is available to simplify installation and maintenance. The 12VL's high pumping efficiencies, ability to handle solids up to 5 1/4 inches in diameter and 2 available motor speeds make it ideal for most high flow wastewater applications.

Advantages By Design
High efficiency hydraulic design cuts pumping costs and extends life of fluid end components.

  • Two-vane, rounded port impellers handle solids with ease at high operating efficiencies.
  • Modified, constant velocity volute offers quiet operation, low radial loads over extended portion of performance curve.

Durable Motor Will Deliver Many Years Of Reliable Service

  • Oil-filled motor and seal cavity for maximum heat dissipation and continuous bearing lubrication.
  • Heat sensor thermostats imbedded in windings protect motor from overheat conditions.
  • Seal leak probes warn of moisture entry; helps prevent costly motor burn-out.
Contact Us Search by Specification
Unit of Measure
Items
Myers® 12VL and 12VLX Series 12 in Submersible Non-Clog Wastewater Pumps

Standard 12" Submersible Non-Clog Wastewater Pumps
Myers® 12VL and 12VLX Series 12 in Submersible Non-Clog Wastewater Pumps

Standard 12" Submersible Non-Clog Wastewater Pumps
Myers® 12VL and 12VLX Series 12 in Submersible Non-Clog Wastewater Pumps

Standard 12" Submersible Non-Clog Wastewater Pumps
Myers® 12VL and 12VLX Series 12 in Submersible Non-Clog Wastewater Pumps

Standard 12" Submersible Non-Clog Wastewater Pumps
Myers® 12VL and 12VLX Series 12 in Submersible Non-Clog Wastewater Pumps

Standard 12" Submersible Non-Clog Wastewater Pumps
Head N/A 72 ft21.9 m
Solids Handling (Diameter) N/A 5 1/4 in133.3 mm
Liquids Handling N/A Drain Water Effluent Raw Unscreened Sewage
Intermittent Liquid Temperature N/A up to 140 ºFup to 60 ºC
Winding Insulation Temperature. (Class H) N/A 356 ºF180 ºC
Motor Electrical Data N/A 1150 RPM: 40, 50 hp, 3 ph
230, 460 & 575 volts, 60 Hz
60, 75 hp, 3 ph
460 & 575 volts, 60 Hz 870 RPM: 15, 20, 25 hp, 3 ph
208, 230, 460 & 575 volts, 60 Hz
30 hp, 3 ph,
230, 460 & 575 volts, 60 Hz
Acceptable pH Range N/A 6 to 9
Specific Gravity N/A 0.9 to 1.1
Viscosity N/A 28 to 35 SSU
Horizontal Discharge Flange N/A 12 in 125 lb. ANSI 304.8 mm
Motor Housing Material N/A Cast Iron, Class 30, ASTM A48
Seal Housing Material N/A Cast Iron, Class 30, ASTM A48
Volute Case Material N/A Cast Iron, Class 30, ASTM A48
Cord Cap Material N/A Cast Iron, Class 30, ASTM A48
Enclosed 2-Vane Impeller Material N/A Ductile Iron, Class 65, ASTM A536
Power Cord Material N/A 25 ft. SOOW
Control Cord Material N/A 25 ft. SOOW
Standard Double Tandem Mechanical Seal Material N/A Carbon & Ceramic
Optional Double Tandem Mechanical Seal Material N/A Lower Tungsten, Carbide
Pump Shaft Material N/A 416 SST
Motor Shaft Material N/A 416 SST
Fasteners Material N/A 300 series SST
Case Wear Ring Materials N/A Bronze
Speed N/A 870 rpm
Power N/A 15 hp N/A 15 hp N/A 15 hp N/A 15 hp N/A 20 hp
Voltage N/A 200 V N/A 230 V N/A 460 V N/A 575 V N/A 200 V
Phase N/A 3
Frequency N/A 60 Hz
Start N/A 334 A116 kV·A N/A 290 A116 kV·A N/A 145 A116 kV·A N/A 116 A116 kV·A N/A 334 A116 kV·A
Run N/A 53.4 A13.4 kW18.5 kV·A N/A 46.4 A13.4 kW18.5 kV·A N/A 23.2 A13.4 kW18.5 kV·A N/A 18.6 A13.4 kW18.5 kV·A N/A 67.2 A17.6 kW23.2 kV·A
NEC Code Letter N/A J N/A J N/A J N/A J N/A G
Service Factor N/A 61.2 A15.8 kW1.2 N/A 53.2 A15.8 kW1.2 N/A 26.6 A15.8 kW1.2 N/A 21.3 A15.8 kW1.2 N/A 78.5 A20.9 kW1.2
Capacity N/A 7,750 gpm29,331 lpm
Agency Approvals N/A

Note N/A Consult factory for applications outside of these recommendations.