Contact Us

Capacity : 7,750 gpm (29,331 lpm)
Head : 72 ft (21.9 m)

Standard (12VL) and Explosion-Proof (12VLX)

The Myers 12VL Submersible non-clog Sewage Pumps are designed especially for high flow, medium head applications such as: Large municipal lift stations, treatment plants, transfer stations and dewatering. A quick removal type rail system is available to simplify installation and maintenance. The 12VL's high pumping efficiencies, ability to handle solids up to 5 1/4 inches in diameter and 2 available motor speeds make it ideal for most high flow wastewater applications.

Advantages By Design
High efficiency hydraulic design cuts pumping costs and extends life of fluid end components.

  • Two-vane, rounded port impellers handle solids with ease at high operating efficiencies.
  • Modified, constant velocity volute offers quiet operation, low radial loads over extended portion of performance curve.

Durable Motor Will Deliver Many Years Of Reliable Service

  • Oil-filled motor and seal cavity for maximum heat dissipation and continuous bearing lubrication.
  • Heat sensor thermostats imbedded in windings protect motor from overheat conditions.
  • Seal leak probes warn of moisture entry; helps prevent costly motor burn-out.
Unit of Measure

Specifications

Head

 N/A 72 ft21.9 m

Solids Handling (Diameter)

 N/A 5 1/4 in133.3 mm

Liquids Handling

 N/A Drain Water Effluent Raw Unscreened Sewage

Intermittent Liquid Temperature

 N/A up to 140 ºFup to 60 ºC

Winding Insulation Temperature. (Class H)

 N/A 356 ºF180 ºC

Motor Electrical Data

 N/A 1150 RPM: 40, 50 hp, 3 ph
230, 460 & 575 volts, 60 Hz
60, 75 hp, 3 ph
460 & 575 volts, 60 Hz 870 RPM: 15, 20, 25 hp, 3 ph
208, 230, 460 & 575 volts, 60 Hz
30 hp, 3 ph,
230, 460 & 575 volts, 60 Hz

Acceptable pH Range

 N/A 6 to 9

Specific Gravity

 N/A 0.9 to 1.1

Viscosity

 N/A 28 to 35 SSU

Horizontal Discharge Flange

 N/A 12 in 125 lb. ANSI 304.8 mm

Speed

 N/A 870 rpm

Power

 N/A 20 hp

Voltage

 N/A 460 V

Phase

 N/A 3

Frequency

 N/A 60 Hz

Start

 N/A 145 A116 kV·A

Run

 N/A 31.8 A17.6 kW23.2 kV·A

NEC Code Letter

 N/A G

Service Factor

 N/A 38.1 A20.9 kW1.2

Capacity

 N/A 7,750 gpm29,331 lpm

Note

 N/A Consult factory for applications outside of these recommendations.
FM Class 1, Groups C & D

Construction Material

Motor Housing Material

 N/A Cast Iron, Class 30, ASTM A48

Seal Housing Material

 N/A Cast Iron, Class 30, ASTM A48

Volute Case Material

 N/A Cast Iron, Class 30, ASTM A48

Cord Cap Material

 N/A Cast Iron, Class 30, ASTM A48

Enclosed 2-Vane Impeller Material

 N/A Ductile Iron, Class 65, ASTM A536

Power Cord Material

 N/A 25 ft. SOOW

Control Cord Material

 N/A 25 ft. SOOW

Standard Double Tandem Mechanical Seal Material

 N/A Carbon & Ceramic

Optional Double Tandem Mechanical Seal Material

 N/A Lower Tungsten, Carbide

Pump Shaft Material

 N/A 416 SST

Motor Shaft Material

 N/A 416 SST

Fasteners Material

 N/A 300 series SST

Case Wear Ring Materials

 N/A Bronze

Agency Approvals

Agency Approvals

 N/A