Capacity : 7,750 gpm (29,331 lpm)
Head : 72 ft (21.9 m)
Standard (12VL) and Explosion-Proof (12VLX)
The Myers 12VL Submersible non-clog Sewage Pumps are designed especially for high flow, medium head applications such as: Large municipal lift stations, treatment plants, transfer stations and dewatering. A quick removal type rail system is available to simplify installation and maintenance. The 12VL's high pumping efficiencies, ability to handle solids up to 5 1/4 inches in diameter and 2 available motor speeds make it ideal for most high flow wastewater applications.
Advantages By Design
High efficiency hydraulic design cuts pumping costs and extends life of fluid end components.
Durable Motor Will Deliver Many Years Of Reliable Service
| Items |
 12VL150M8-03 Standard 12" Submersible Non-Clog Wastewater Pumps |
12VL150M8-23 Standard 12" Submersible Non-Clog Wastewater Pumps |
12VL150M8-43 Standard 12" Submersible Non-Clog Wastewater Pumps |
12VL150M8-53 Standard 12" Submersible Non-Clog Wastewater Pumps |
12VL200M8-03 Standard 12" Submersible Non-Clog Wastewater Pumps |
|||||
| Head | 72 ft21.9 m | |||||||||
| Solids Handling (Diameter) | 5 1/4 in133.3 mm | |||||||||
| Liquids Handling | Drain Water Effluent Raw Unscreened Sewage | |||||||||
| Intermittent Liquid Temperature | up to 140 ºFup to 60 ºC | |||||||||
| Winding Insulation Temperature. (Class H) | 356 ºF180 ºC | |||||||||
| Motor Electrical Data |
1150 RPM: 40, 50 hp, 3 ph 230, 460 & 575 volts, 60 Hz 60, 75 hp, 3 ph 460 & 575 volts, 60 Hz 870 RPM: 15, 20, 25 hp, 3 ph 208, 230, 460 & 575 volts, 60 Hz 30 hp, 3 ph, 230, 460 & 575 volts, 60 Hz |
|||||||||
| Acceptable pH Range | 6 to 9 | |||||||||
| Specific Gravity | 0.9 to 1.1 | |||||||||
| Viscosity | 28 to 35 SSU | |||||||||
| Horizontal Discharge Flange | 12 in 125 lb. ANSI 304.8 mm | |||||||||
| Motor Housing Material | Cast Iron, Class 30, ASTM A48 | |||||||||
| Seal Housing Material | Cast Iron, Class 30, ASTM A48 | |||||||||
| Volute Case Material | Cast Iron, Class 30, ASTM A48 | |||||||||
| Cord Cap Material | Cast Iron, Class 30, ASTM A48 | |||||||||
| Enclosed 2-Vane Impeller Material | Ductile Iron, Class 65, ASTM A536 | |||||||||
| Power Cord Material | 25 ft. SOOW | |||||||||
| Control Cord Material | 25 ft. SOOW | |||||||||
| Standard Double Tandem Mechanical Seal Material | Carbon & Ceramic | |||||||||
| Optional Double Tandem Mechanical Seal Material | Lower Tungsten, Carbide | |||||||||
| Pump Shaft Material | 416 SST | |||||||||
| Motor Shaft Material | 416 SST | |||||||||
| Fasteners Material | 300 series SST | |||||||||
| Case Wear Ring Materials | Bronze | |||||||||
| Speed | 870 rpm | |||||||||
| Power | 15 hp | 15 hp | 15 hp | 15 hp | 20 hp | |||||
| Voltage | 200 V | 230 V | 460 V | 575 V | 200 V | |||||
| Phase | 3 | |||||||||
| Frequency | 60 Hz | |||||||||
| Start | 334 A116 kV·A | 290 A116 kV·A | 145 A116 kV·A | 116 A116 kV·A | 334 A116 kV·A | |||||
| Run | 53.4 A13.4 kW18.5 kV·A | 46.4 A13.4 kW18.5 kV·A | 23.2 A13.4 kW18.5 kV·A | 18.6 A13.4 kW18.5 kV·A | 67.2 A17.6 kW23.2 kV·A | |||||
| NEC Code Letter | J | J | J | J | G | |||||
| Service Factor | 61.2 A15.8 kW1.2 | 53.2 A15.8 kW1.2 | 26.6 A15.8 kW1.2 | 21.3 A15.8 kW1.2 | 78.5 A20.9 kW1.2 | |||||
| Capacity | 7,750 gpm29,331 lpm | |||||||||
| Agency Approvals |
 |
|||||||||
| Note | Consult factory for applications outside of these recommendations. | |||||||||
|
|
||||||||||
